|
GOOD COST PERFORMANCE AND
USER FRIENDLY
Measurement
is carried out accurately and according to the visual image.
Good cost performance has been achieved by efforts to improve the
functions and operation of the instrument.
USES THE RECTANGULAR
COORDINATE SYSTEM
By the development of a highly efficient non-slip roller, which is made
of special ceramic, and by use of linear rails, measurement can be made
exactly as intended, without slip or miss.
COMPLETE WITH EXTERNAL
OUTPUT STANDARD EQUIPMENT
A printer which helps to record and combine the data into a total.
The RS232C, used as the standard device for direct transfer of the
measurement data.
IMPROVED OPERATION
A complete selection of functions, such as the automatic convergence
function, and the sectional line length measuring function, greatly
improve measuring efficiency. Operation of the instrument is simplified
by using a separate colour sheet key for each function.
HIGHLY REFINED DESIGN
This handy compact instrument can be used anywhere, any time.
Area-marks mean that you can recognize the setting position of the
instrument at a glance.
|
1.HIGHLY ACCURATE, HIGH DISSOLUTION CAPACITY.
Using our own special sensor technology, we have managed to achieve a
rate of accuracy of 0.1%, and a dissolution capacity of 0.05mm.
2.SIMULTANEOUS MEASUREMENT OF
AREA AND LINE.
The KP-800 measures both the area and line with just one action.
3.SECTIONAL LINE LENGTH
MEASUREMENT FUNCTION.
Using this function the length of a line between two points can be
measured. More efficient than using the line length measurement mode
for repeated measurement.
4.IMPROVED OPERATION USING THE
POINT MODE.
Using the point mode the straight line part of a figure can be measured
simply by indication the end points of the lines.
In the case of curved line the continuity function is used.
5.THE AUTOMATIC CONVERGENCE FUNCTION.
When measuring a closed figure, with the starting point already
recorded, when the closing point comes within a 0.5mm radius of the
starting point, the instrument automatically converges the two lines
and finishes the measurement.
6.MEASUREMENT OF ACCUMULATED
DATA AND AVERAGES.
The instrument can record up to 100 times the accumulated and average
data of both the area and the line each time it is measured.
7.UNIT SELECTION FUNCTION.
Selection can be made of either the metric unit (mm.cm.m.km.) or the
imperial unit (in.ft.acre/yards.mi).
8.USER-OPTINAL UNIT SETTING
FUNCTION.
The user also has the option of setting units other than metrics or
imperials.
9.AUTOMATIC UNIT PROCESSING
FUNCTION.
If the number exceeds 10 digits in the unit it is displayed in, the
display automatically converts to a higher unit.
10.REDUCED SCALE SETTING
FUNCTION.
The instrument has a wide range of reduced scale settings.
Which can be set separately horizontally and vertically.
11.CALCULATING FUNCTION.
Arithmetical calculations can be performed on the numerical value and
the measurement results or the memorise value, as well as a combination
of both.
| Specifications |
| Measuring
function |
Area,
Linear, Sectional line length |
| Units |
Metric
unit : mm. cm. m. km.
Imperial unit: in. ft. acre/yd. mi
Other unit as specified by the user. |
| Display |
16 digit
X 2 line dot matrix type LCD |
| Scope of
measurement |
X axis
250mm Y axis: +/- 6,000mm (12m) |
| Resolution |
0.05mm
with a scale of 100% |
| Accuracy |
Within
0.1% |
| Power
source |
Built-in
rechargeable Ni-Cd battery |
| Operating time |
Continuity
use with the built-in battery,
When the battery is fully recharged : Approx. 30 hrs
(can be used while battery is being recharged) |
| Charging time |
At normal
state approx. 10hrs.
At fully discharged : approx. 15 hrs. |
| Dimensions |
Instrument
only : 84mm x 336mm x 50mm
Original case : 195mm x 365mm x 65mm |
| Weight |
Approx
1kg (Instrument only) |
| Additional items |
Instruction
manual, A/C adapter, original case 3 rolls of
Paper for printer. |
|
|
