GOOD COST PERFORMANCE AND USER FRIENDLY
Measurement is carried out accurately and according to the visual image.
Good cost performance has been achieved by efforts to improve the functions
and operation of the instrument.
USES THE
RECTANGULAR COORDINATE SYSTEM
By the development of a highly efficient non-slip roller, which is made of
special ceramic, and by use of linear rails, measurement can be made exactly
as intended, without slip or miss.
COMPLETE WITH EXTERNAL OUTPUT STANDARD EQUIPMENT
A printer which helps to record and combine the data into a total.
The RS232C, used as the standard device for direct transfer of the
measurement data.
IMPROVED OPERATION
A complete selection of functions, such as the automatic convergence
function, and the sectional line length measuring function, greatly improve
measuring efficiency. Operation of the instrument is simplified by using a
separate colour sheet key for each function.
HIGHLY REFINED DESIGN
This handy compact instrument can be used anywhere, any time.
Area-marks mean that you can recognize the setting position of the
instrument at a glance.
1.HIGHLY ACCURATE, HIGH DISSOLUTION CAPACITY.
Using our own special sensor technology, we have managed to achieve a rate of accuracy of 0.1%, and a dissolution capacity of 0.05mm.
2.SIMULTANEOUS MEASUREMENT OF AREA AND LINE.
The KP-800 measures both the area and line with just one action.
3.SECTIONAL LINE LENGTH MEASUREMENT FUNCTION.
Using this function the length of a line between two points can be measured. More efficient than using the line length measurement mode for repeated measurement.
4.IMPROVED OPERATION USING THE POINT MODE.
Using the point mode the straight line part of a figure can be measured simply by indication the end points of the lines.
In the case of curved line the continuity function is used.
5.THE AUTOMATIC CONVERGENCE FUNCTION.
When measuring a closed figure, with the starting point already recorded, when the closing point comes within a 0.5mm radius of the starting point, the instrument automatically converges the two lines and finishes the measurement.
6.MEASUREMENT OF ACCUMULATED DATA AND AVERAGES.
The instrument can record up to 100 times the accumulated and average data of both the area and the line each time it is measured.
7.UNIT SELECTION FUNCTION.
Selection can be made of either the metric unit (mm.cm.m.km.) or the imperial unit (in.ft.acre/yards.mi).
8.USER-OPTINAL UNIT SETTING FUNCTION.
The user also has the option of setting units other than metrics or imperials.
9.AUTOMATIC UNIT PROCESSING FUNCTION.
If the number exceeds 10 digits in the unit it is displayed in, the display automatically converts to a higher unit.
10.REDUCED SCALE SETTING FUNCTION.
The instrument has a wide range of reduced scale settings.
Which can be set separately horizontally and vertically.
11.CALCULATING FUNCTION.
Arithmetical calculations can be performed on the numerical value and the measurement results or the memories value, as well as a combination of both.
| Measurement functions | Area, Linear, Sectional line length |
| Units |
Metric unit : mm. cm. m. km. Imperial unit: in. ft. acre/yd. mi Other unit as specified by the user. |
| Display | 16 digit x 2 line dot matrix LCD |
| Scope of measurement | X axis 250mm Y axis: +/- 6,000mm (12m) |
| Resolution | 0.05mm with a scale of 100% |
| Accuracy / | Within ± 0.1% |
| Power source | Built-in rechargeable Ni-Cd battery |
| Operating time |
Continuity use with the
built-in battery, When the battery is fully recharged : Approx. 30 hrs (can be used while battery is being recharged) |
| Charging time |
At normal state approx.
10hrs. At fully discharged : approx. 15 hrs. |
| Dimension |
Instrument only : 84mm x
336mm x 50mm Original case : 195mm x 365mm x 65mm |
| Weight | Approx 1kg (Instrument only) |
| Additional items | Instruction manual, A/C adapter, original case 3 rolls of Paper for printer. |